[Novalug] dmesg showing vesafb / drive errors at bottom

Jay Hart jhart@kevla.org
Sat Jan 13 23:50:48 EST 2007


I need to see if my box continues to lock up before I decide what to do next.

If I replace my 3.5" IDE drive with a SATA drive, then I have to re-install.

If I replace the video card, then I have to re-wire the box.

So, I think I will continue to try to resolve my email problem, while seeing
if and when the box locks up.

I have the resolution issue solved for now, thanks to Greg's suggestion.

Jay

> What specifically is failing about the video card?
>
> Does it not give you a screen at all at boot (text mode)
> Or is X not loading?
>
> I'm not sure that it was really clearly defined.
>
> I just want to make sure that we're not blurring any lines (know what I
> mean?).
>
> k
>
> Jay Hart wrote:
>>> Try adding "noapic" to the kernel line.
>>
>> What do you think this would fix?
>>
>> I did another xorgcfg, after rebooting box. It locked it up again.
>>
>> So, at this point I'm going to install my new SATA drive, that should clear
>> the drive errors, which are most likely being caused by a 2.5 and 3.5 IDE
>> drive using same bus, which I can't split due to space limitations.
>>
>> And, I'm going to try using a different video device. Hopefully Dan Arico
>> and
>> I can get together tomorrow, so I might be able to pick up several he has.
>>
>> So, I think I'm going to go watch the football game.
>>
>> Thanks for every ones help. I'll check email in about ten minutes for
>> replies.
>>
>> Jay
>>
>>>
>>> Jay Hart wrote:
>>>> I am including my dmesg file, showing what type of video "device" system
>>>> is
>>>> detecting.  I can include more info if needed. What I am trying to do is
>>>> to
>>>> see if I can find another driver to use for the video device.
>>>>
>>>> I booted into init 3, and ran xorgcfg, and got nothing but a blank screen
>>>> for
>>>> my efforts.
>>>>
>>>> Linux version 2.6.18.2-34-default (geeko@buildhost) (gcc version 4.1.2
>>>> 20061115 (prerelease) (SUSE Linux)) #1 SMP Mon Nov 27 11:46:27 UTC 2006
>>>> BIOS-provided physical RAM map:
>>>>  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
>>>>  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
>>>>  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
>>>>  BIOS-e820: 0000000000100000 - 000000001bee0000 (usable)
>>>>  BIOS-e820: 000000001bee0000 - 000000001bee3000 (ACPI NVS)
>>>>  BIOS-e820: 000000001bee3000 - 000000001bef0000 (ACPI data)
>>>>  BIOS-e820: 000000001bef0000 - 000000001bf00000 (reserved)
>>>>  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
>>>>  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
>>>>  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
>>>> 0MB HIGHMEM available.
>>>> 446MB LOWMEM available.
>>>> found SMP MP-table at 000f51e0
>>>> On node 0 totalpages: 114400
>>>>   DMA zone: 4096 pages, LIFO batch:0
>>>>   Normal zone: 110304 pages, LIFO batch:31
>>>> DMI 2.3 present.
>>>> Using APIC driver default
>>>> IO/L-APIC allowed because system is MP or new enough
>>>> ACPI: RSDP (v000 CN700                                 ) @ 0x000f72a0
>>>> ACPI: RSDT (v001 CN700  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1bee3040
>>>> ACPI: FADT (v001 CN700  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1bee30c0
>>>> ACPI: MADT (v001 CN700  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1bee9080
>>>> ACPI: DSDT (v001 CN700  AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
>>>> ACPI: PM-Timer IO Port: 0x408
>>>> ACPI: Local APIC address 0xfee00000
>>>> ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
>>>> Processor #0 6:10 APIC version 20
>>>> ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
>>>> ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
>>>> IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
>>>> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
>>>> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
>>>> ACPI: IRQ0 used by override.
>>>> ACPI: IRQ2 used by override.
>>>> ACPI: IRQ9 used by override.
>>>> Enabling APIC mode:  Flat.  Using 1 I/O APICs
>>>> Using ACPI (MADT) for SMP configuration information
>>>> Allocating PCI resources starting at 20000000 (gap: 1bf00000:e2d00000)
>>>> Detected 1500.153 MHz processor.
>>>> Built 1 zonelists.  Total pages: 114400
>>>> Kernel command line: root=/dev/hda1 vga=0x317    resume=/dev/hda9
>>>> splash=silent
>>>> bootsplash: silent mode.
>>>> mapped APIC to ffffd000 (fee00000)
>>>> mapped IOAPIC to ffffc000 (fec00000)
>>>> Enabling fast FPU save and restore... done.
>>>> Enabling unmasked SIMD FPU exception support... done.
>>>> Initializing CPU#0
>>>> PID hash table entries: 2048 (order: 11, 8192 bytes)
>>>> Console: colour dummy device 80x25
>>>> Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
>>>> Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
>>>> Memory: 446888k/457600k available (1697k kernel code, 10168k reserved,
>>>> 968k
>>>> data, 196k init, 0k highmem)
>>>> Checking if this processor honours the WP bit even in supervisor mode...
>>>> Ok.
>>>> Calibrating delay using timer specific routine.. 3002.19 BogoMIPS
>>>> (lpj=6004393)
>>>> Security Framework v1.0.0 initialized
>>>> Mount-cache hash table entries: 512
>>>> CPU: After generic identify, caps: a7c9baff 00100000 00000000 00000000
>>>> 00000181 00000000 00000000
>>>> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
>>>> CPU: L2 Cache: 128K (64 bytes/line)
>>>> CPU: After all inits, caps: 27c9baff 00100000 00000000 00000000 00000181
>>>> 00003fcc 00000000
>>>> Compat vDSO mapped to ffffe000.
>>>> Checking 'hlt' instruction... OK.
>>>> SMP alternatives: switching to UP code
>>>> Freeing SMP alternatives: 16k freed
>>>> checking if image is initramfs... it is
>>>> Freeing initrd memory: 2855k freed
>>>> ACPI: Core revision 20060707
>>>> CPU0: Centaur VIA Esther processor 1500MHz stepping 09
>>>> Total of 1 processors activated (3002.19 BogoMIPS).
>>>> ENABLING IO-APIC IRQs
>>>> ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
>>>> Brought up 1 CPUs
>>>> migration_cost=0
>>>> NET: Registered protocol family 16
>>>> ACPI: bus type pci registered
>>>> PCI: PCI BIOS revision 2.10 entry at 0xfb5c0, last bus=1
>>>> PCI: Using configuration type 1
>>>> Setting up standard PCI resources
>>>> ACPI: Interpreter enabled
>>>> ACPI: Using IOAPIC for interrupt routing
>>>> ACPI: PCI Root Bridge [PCI0] (0000:00)
>>>> PCI: Probing PCI hardware (bus 00)
>>>> Boot video device is 0000:01:00.0
>>>> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
>>>> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12)
>>>> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
>>>> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 *7 10 11 12)
>>>> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *5
>>>> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
>>>> ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
>>>> ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
>>>> ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
>>>> ACPI: PCI Interrupt Link [ALKA] (IRQs *20)
>>>> ACPI: PCI Interrupt Link [ALKB] (IRQs *21)
>>>> ACPI: PCI Interrupt Link [ALKC] (IRQs *22), disabled.
>>>> ACPI: PCI Interrupt Link [ALKD] (IRQs *23)
>>>> Linux Plug and Play Support v0.97 (c) Adam Belay
>>>> pnp: PnP ACPI init
>>>> pnp: PnP ACPI: found 10 devices
>>>> PnPBIOS: Disabled by ACPI PNP
>>>> PCI: Using ACPI for IRQ routing
>>>> PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a
>>>> report
>>>> pnp: 00:02: ioport range 0x400-0x47f could not be reserved
>>>> pnp: 00:02: ioport range 0x500-0x50f has been reserved
>>>> PCI: Bridge: 0000:00:01.0
>>>>   IO window: e000-efff
>>>>   MEM window: fb000000-fcffffff
>>>>   PREFETCH window: f4000000-f7ffffff
>>>> PCI: Setting latency timer of device 0000:00:01.0 to 64
>>>> NET: Registered protocol family 2
>>>> IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
>>>> TCP established hash table entries: 16384 (order: 5, 131072 bytes)
>>>> TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
>>>> TCP: Hash tables configured (established 16384 bind 8192)
>>>> TCP reno registered
>>>> apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
>>>> apm: overridden by ACPI.
>>>> audit: initializing netlink socket (disabled)
>>>> audit(1168726159.096:1): initialized
>>>> Total HugeTLB memory allocated, 0
>>>> VFS: Disk quotas dquot_6.5.1
>>>> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
>>>> Initializing Cryptographic API
>>>> io scheduler noop registered
>>>> io scheduler anticipatory registered
>>>> io scheduler deadline registered
>>>> io scheduler cfq registered (default)
>>>> 0000:00:10.4 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
>>>> PCI: Bypassing VIA 8237 APIC De-Assert Message
>>>> vesafb: framebuffer at 0xf4000000, mapped to 0xdc880000, using 6144k,
>>>> total
>>>> 65536k
>>>> vesafb: mode is 1024x768x16, linelength=2048, pages=41
>>>> vesafb: protected mode interface info at c000:a971
>>>> vesafb: pmi: set display start = c00ca9bf, set palette = c00caa30
>>>> vesafb: scrolling: redraw
>>>> vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
>>>> bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size
>>>> 81749
>>>> bytes,<6>...found (1024x768, 46202 bytes, v3).
>>>> Console: switching to colour frame buffer device 124x44
>>>> fb0: VESA VGA frame buffer device
>>>> isapnp: Scanning for PnP cards...
>>>> isapnp: No Plug & Play device found
>>>> Real Time Clock Driver v1.12ac
>>>> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
>>>> floppy0: no floppy controllers found
>>>> RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
>>>> PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
>>>> serio: i8042 AUX port at 0x60,0x64 irq 12
>>>> serio: i8042 KBD port at 0x60,0x64 irq 1
>>>> mice: PS/2 mouse device common for all mice
>>>> input: PC Speaker as /class/input/input0
>>>> input: AT Translated Set 2 keyboard as /class/input/input1
>>>> md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
>>>> md: bitmap version 4.39
>>>> NET: Registered protocol family 1
>>>> Using IPI No-Shortcut mode
>>>> ACPI: (supports S0 S1 S4 S5)
>>>> Freeing unused kernel memory: 196k freed
>>>> Time: tsc clocksource has been installed.
>>>> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
>>>> ide: Assuming 33MHz system bus speed for PIO modes; override with
>>>> idebus=xx
>>>> SCSI subsystem initialized
>>>> ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
>>>> ACPI: Processor [CPU0] (supports 2 throttling states)
>>>> ACPI: Thermal Zone [THRM] (40 C)
>>>> libata version 2.00 loaded.
>>>> sata_via 0000:00:0f.0: version 2.0
>>>> ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
>>>> ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [ALKA] -> GSI 20 (level, low)
>>>> ->
>>>> IRQ 169
>>>> sata_via 0000:00:0f.0: routed to hard irq line 11
>>>> ata1: SATA max UDMA/133 cmd 0xFE00 ctl 0xFD02 bmdma 0xFA00 irq 169
>>>> ata2: SATA max UDMA/133 cmd 0xFC00 ctl 0xFB02 bmdma 0xFA08 irq 169
>>>> scsi0 : sata_via
>>>> input: ImExPS/2 Generic Explorer Mouse as /class/input/input2
>>>> Time: acpi_pm clocksource has been installed.
>>>> input: AT Translated Set 2 keyboard as /class/input/input3
>>>> ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
>>>> ATA: abnormal status 0x7F on port 0xFE07
>>>> scsi1 : sata_via
>>>> ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
>>>> ATA: abnormal status 0x7F on port 0xFC07
>>>> VP_IDE: IDE controller at PCI slot 0000:00:0f.1
>>>> ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [ALKA] -> GSI 20 (level, low)
>>>> ->
>>>> IRQ 169
>>>> PCI: VIA IRQ fixup for 0000:00:0f.1, from 255 to 9
>>>> VP_IDE: chipset revision 6
>>>> VP_IDE: not 100% native mode: will probe irqs later
>>>> VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
>>>>     ide0: BM-DMA at 0xf900-0xf907, BIOS settings: hda:DMA, hdb:DMA
>>>>     ide1: BM-DMA at 0xf908-0xf90f, BIOS settings: hdc:DMA, hdd:pio
>>>> Probing IDE interface ide0...
>>>> hda: Hitachi HDS721680PLAT80, ATA DISK drive
>>>> hdb: ST96812A, ATA DISK drive
>>>> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>>>> hda: max request size: 512KiB
>>>> hda: 160836480 sectors (82348 MB) w/7384KiB Cache, CHS=16383/255/63,
>>>> UDMA(133)
>>>> hda: cache flushes supported
>>>>  hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 >
>>>> hdb: max request size: 512KiB
>>>> hdb: 117210240 sectors (60011 MB) w/8192KiB Cache, CHS=16383/255/63,
>>>> UDMA(100)
>>>> hdb: cache flushes supported
>>>>  hdb: hdb1 hdb2 < hdb5 >
>>>> Probing IDE interface ide1...
>>>> hdc: QSI CD-RW/DVD-ROM SBW-243, ATAPI CD/DVD-ROM drive
>>>> ide1 at 0x170-0x177,0x376 on irq 15
>>>> ACPI: Fan [FAN] (on)
>>>> BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
>>>> Attempting manual resume
>>>> kjournald starting.  Commit interval 5 seconds
>>>> EXT3 FS on hda1, internal journal
>>>> EXT3-fs: mounted filesystem with ordered data mode.
>>>> usbcore: registered new driver usbfs
>>>> usbcore: registered new driver hub
>>>> pci_hotplug: PCI Hot Plug PCI Core version: 0.5
>>>> shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
>>>> Linux agpgart interface v0.101 (c) Dave Jones
>>>> USB Universal Host Controller Interface driver v3.0
>>>> ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
>>>> ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low)
>>>> ->
>>>> IRQ 177
>>>> PCI: VIA IRQ fixup for 0000:00:10.0, from 10 to 1
>>>> uhci_hcd 0000:00:10.0: UHCI Host Controller
>>>> uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
>>>> uhci_hcd 0000:00:10.0: irq 177, io base 0x0000f800
>>>> usb usb1: new device found, idVendor=0000, idProduct=0000
>>>> usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
>>>> usb usb1: Product: UHCI Host Controller
>>>> usb usb1: Manufacturer: Linux 2.6.18.2-34-default uhci_hcd
>>>> usb usb1: SerialNumber: 0000:00:10.0
>>>> usb usb1: configuration #1 chosen from 1 choice
>>>> hub 1-0:1.0: USB hub found
>>>> hub 1-0:1.0: 2 ports detected
>>>> ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKB] -> GSI 21 (level, low)
>>>> ->
>>>> IRQ 177
>>>> PCI: VIA IRQ fixup for 0000:00:10.1, from 10 to 1
>>>> uhci_hcd 0000:00:10.1: UHCI Host Controller
>>>> uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
>>>> uhci_hcd 0000:00:10.1: irq 177, io base 0x0000f700
>>>> usb usb2: new device found, idVendor=0000, idProduct=0000
>>>> usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
>>>> usb usb2: Product: UHCI Host Controller
>>>> usb usb2: Manufacturer: Linux 2.6.18.2-34-default uhci_hcd
>>>> usb usb2: SerialNumber: 0000:00:10.1
>>>> usb usb2: configuration #1 chosen from 1 choice
>>>> hub 2-0:1.0: USB hub found
>>>> hub 2-0:1.0: 2 ports detected
>>>> ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [ALKB] -> GSI 21 (level, low)
>>>> ->
>>>> IRQ 177
>>>> PCI: VIA IRQ fixup for 0000:00:10.2, from 11 to 1
>>>> uhci_hcd 0000:00:10.2: UHCI Host Controller
>>>> uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
>>>> uhci_hcd 0000:00:10.2: irq 177, io base 0x0000f600
>>>> usb usb3: new device found, idVendor=0000, idProduct=0000
>>>> usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
>>>> usb usb3: Product: UHCI Host Controller
>>>> usb usb3: Manufacturer: Linux 2.6.18.2-34-default uhci_hcd
>>>> usb usb3: SerialNumber: 0000:00:10.2
>>>> usb usb3: configuration #1 chosen from 1 choice
>>>> hub 3-0:1.0: USB hub found
>>>> hub 3-0:1.0: 2 ports detected
>>>> ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [ALKB] -> GSI 21 (level, low)
>>>> ->
>>>> IRQ 177
>>>> PCI: VIA IRQ fixup for 0000:00:10.3, from 11 to 1
>>>> uhci_hcd 0000:00:10.3: UHCI Host Controller
>>>> uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
>>>> uhci_hcd 0000:00:10.3: irq 177, io base 0x0000f500
>>>> usb usb4: new device found, idVendor=0000, idProduct=0000
>>>> usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
>>>> usb usb4: Product: UHCI Host Controller
>>>> usb usb4: Manufacturer: Linux 2.6.18.2-34-default uhci_hcd
>>>> usb usb4: SerialNumber: 0000:00:10.3
>>>> usb usb4: configuration #1 chosen from 1 choice
>>>> hub 4-0:1.0: USB hub found
>>>> hub 4-0:1.0: 2 ports detected
>>>> agpgart: Detected VIA P4M800CE chipset
>>>> agpgart: AGP aperture is 128M @ 0xe8000000
>>>> ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low)
>>>> ->
>>>> IRQ 177
>>>> PCI: VIA IRQ fixup for 0000:00:10.4, from 7 to 1
>>>> ehci_hcd 0000:00:10.4: EHCI Host Controller
>>>> ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
>>>> ehci_hcd 0000:00:10.4: irq 177, io mem 0xfdffe000
>>>> ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
>>>> usb usb5: new device found, idVendor=0000, idProduct=0000
>>>> usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
>>>> usb usb5: Product: EHCI Host Controller
>>>> usb usb5: Manufacturer: Linux 2.6.18.2-34-default ehci_hcd
>>>> usb usb5: SerialNumber: 0000:00:10.4
>>>> usb usb5: configuration #1 chosen from 1 choice
>>>> hub 5-0:1.0: USB hub found
>>>> hub 5-0:1.0: 8 ports detected
>>>> hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
>>>> Uniform CD-ROM driver Revision: 3.20
>>>> ieee1394: Initialized config rom entry `ip1394'
>>>> ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 19 (level, low) -> IRQ 185
>>>> ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[185]
>>>> MMIO=[fdfff000-fdfff7ff]
>>>> Max Packet=[2048]  IR/IT contexts=[4/8]
>>>> via-rhine.c:v1.10-LK1.4.1 July-24-2006 Written by Donald Becker
>>>> ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
>>>> ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKD] -> GSI 23 (level, low)
>>>> ->
>>>> IRQ 193
>>>> eth0: VIA Rhine II at 0x1f000, 00:30:18:ae:0a:e2, IRQ 193.
>>>> eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link
>>>> 45e1.
>>>> ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0030180000ab8f4c]
>>>> Adding 2666748k swap on /dev/hda9.  Priority:-1 extents:1 across:2666748k
>>>> device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised:
>>>> dm-devel@redhat.com
>>>> loop: loaded (max 8 devices)
>>>> kjournald starting.  Commit interval 5 seconds
>>>> EXT3 FS on hda8, internal journal
>>>> EXT3-fs: mounted filesystem with ordered data mode.
>>>> kjournald starting.  Commit interval 5 seconds
>>>> EXT3 FS on hdb1, internal journal
>>>> EXT3-fs: mounted filesystem with ordered data mode.
>>>> kjournald starting.  Commit interval 5 seconds
>>>> EXT3 FS on hda7, internal journal
>>>> EXT3-fs: mounted filesystem with ordered data mode.
>>>> kjournald starting.  Commit interval 5 seconds
>>>> EXT3 FS on hda5, internal journal
>>>> EXT3-fs: mounted filesystem with ordered data mode.
>>>> kjournald starting.  Commit interval 5 seconds
>>>> EXT3 FS on hda6, internal journal
>>>> EXT3-fs: mounted filesystem with ordered data mode.
>>>> kjournald starting.  Commit interval 5 seconds
>>>> EXT3 FS on hdb5, internal journal
>>>> EXT3-fs: mounted filesystem with ordered data mode.
>>>> AppArmor: AppArmor initialized
>>>> audit(1168726189.633:2): AppArmor initialized
>>>>
>>>> ACPI: Power Button (FF) [PWRF]
>>>> ACPI: Power Button (CM) [PWRB]
>>>> powernow: This module only works with AMD K7 CPUs
>>>> acpi-cpufreq: CPU0 - ACPI performance management activated.
>>>> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
>>>> audit(1168744205.014:3): audit_pid=3190 old=0 by auid=4294967295
>>>> NET: Registered protocol family 10
>>>> lo: Disabled Privacy Extensions
>>>> IPv6 over IPv4 tunneling driver
>>>> eth0: no IPv6 routers present
>>>> hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
>>>> hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
>>>> ide: failed opcode was: unknown
>>>>
>>>>
>>>> _______________________________________________
>>>> Novalug mailing list
>>>> Novalug@calypso.tux.org
>>>> http://calypso.tux.org/cgi-bin/mailman/listinfo/novalug
>>>
>>
>>
>
>





More information about the Novalug mailing list